|
 |
|
|
 |
More
Information |
|
|
|
 |
 |
|
|
|
»User
Guide |
|
|
|
»Brochure |
|
|
|
»USB
Driver |
|
|
|
»FAQs
& Troubleshooting |
|
|
|
 |
|
|
|
»QIG |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
 |
 |
 |
 |
|
|
|
|
|
Features
The
Prolink Hurricane 9000P is an Ethernet ADSL Bridge/Router
with 4-port 10/100 switch, which fully
complies to ANSI T1.413 Issue 2, ITU-T G.992.1 (G.dmt)
and G.992.2 (G.lite) ADSL standards. It supports Full-Rate
ADSL transmission at up to 8Mbps downstream and up to
1Mbps upstream. It can be connected to
a small, home-office LAN or a single Ethernet-equipped
PC to provide broadband services to a single/multi-user environment
with support both Static and Dynamic IP Routing,
Network Address Translation and Dynamic Host Configuration
Protocol Server.
Specifications
ADSL
Compliance
-
Compliant
with ADSL standards
-
Full-rate
ANSI T1.413 Issue 2 and ITU G.dmt (G.992.1) standards
-
Splitterless
ITU G.lite (G.992.2) specification
-
ADSL over
POTS (Annex A) and ADSL over ISDN (Annex B)
-
DMT modulation
and demodulation
-
Full-rate
adaptive modem
-
Maximum downstream
rate of 8 Mbps
-
Maximum upstream
rate of 1 Mbps
-
Tone detection
for low power mode
-
Supports splitterless
ADSL implementation
-
Supports Dying
Gasp
-
WAN mode support:
PPP over ATM (RFC 2364) and PPP overEthernet (RFC2516)
-
LAN mode support:
bridged/routed Ethernet over ATM (RFC1483) and Classical
IP over ATM (RFC 1577)
-
ATM Forum
UNI 3.1/4.0 PVC
-
Up to 8 VCs
(Virtual Circuits)
-
ATM SAR (Segmentation
and Reassembly)
-
ATM AAL5 (Adaption
Layer type 5)
-
OAM F4/F5
Bridge
Mode
-
IP routing&RIPv2
-
Static routing
-
DHCP (Dynamic
Host Configuration Protocol) Server and Client
-
NAPT (Network
Address and Port Translation)
-
NAT (Network
Address Translation)
-
ICMP (Internet
Control Message Protocol)
-
Simultaneous
USB and Ethernet operation
-
User authentication
for PPP
-
PAP (Password
Authentication Protocol)
-
CHAP (Challenge
Authentication Protocol)
-
Password protected
system management
HTTP
Web-based management
-
Firmware upgrade
via FTP
-
WAN and LAN
side connection statistics
-
Configuration
of static routes and Routing table
-
Configuration
of NAT/NAPT
-
Password protected
access (Admin/User)
-
Selection
of Bridge or Router Mode
-
PPP user ID
and password
-
Configuration
of VCs (Virtual Circuits)
-
Power Switch
-
Power Connector
-
Reset Button
- 4 x RJ45 LAN
Connector
-
1 x USB Connector
-
1 x RJ11 Connector
- Power LED
- ADSL LED
- 4 x LAN LED
- Specifications are subjected to change without prior notice
|
|
|
|
|
|
|
|
|
|
|
|